Dear Freesurfer experts,
When I use Freeview GUI to show overlays on a surface, I can click on the button "Configure", and then check the box "Enable" in the smooth section (upper right of the pop-out window), to smooth it. Is there any options to do similar stuff in the command line of freeview? e.g. when I want to generate a lot of screenshots by the -ss option. Thank you in advance!
best Peng
Hi Peng,
No, there is no command-line option for that. I will add it in future update.
Best, Ruopeng
On Jan 27, 2017, at 9:49 AM, peng prion.w@gmail.com wrote:
Dear Freesurfer experts,
When I use Freeview GUI to show overlays on a surface, I can click on the button "Configure", and then check the box "Enable" in the smooth section (upper right of the pop-out window), to smooth it. Is there any options to do similar stuff in the command line of freeview? e.g. when I want to generate a lot of screenshots by the -ss option. Thank you in advance!
best Peng _______________________________________________ Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
probably you should just smooth the volume and save it as a new volume before running freeview
cheers Bruce On Fri, 27 Jan 2017, Ruopeng Wang wrote:
Hi Peng,
No, there is no command-line option for that. I will add it in future update.
Best, Ruopeng
On Jan 27, 2017, at 9:49 AM, peng prion.w@gmail.com wrote:
Dear Freesurfer experts,
When I use Freeview GUI to show overlays on a surface, I can click on the button "Configure", and then check the box "Enable" in the smooth section (upper right of the pop-out window), to smooth it. Is there any options to do similar stuff in the command line of freeview? e.g. when I want to generate a lot of screenshots by the -ss option. Thank you in advance!
best Peng _______________________________________________ Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Thanks for the advice, bruce.
On Fri, Jan 27, 2017 at 4:17 PM, Bruce Fischl fischl@nmr.mgh.harvard.edu wrote:
probably you should just smooth the volume and save it as a new volume before running freeview
cheers Bruce On Fri, 27 Jan 2017, Ruopeng Wang wrote:
Hi Peng,
No, there is no command-line option for that. I will add it in future update.
Best, Ruopeng
On Jan 27, 2017, at 9:49 AM, peng prion.w@gmail.com wrote:
Dear Freesurfer experts,
When I use Freeview GUI to show overlays on a surface, I can click on the button "Configure", and then check the box "Enable" in the smooth section (upper right of the pop-out window), to smooth it. Is there any options to do similar stuff in the command line of freeview? e.g. when I want to generate a lot of screenshots by the -ss option. Thank you in advance!
best Peng _______________________________________________ Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
The information in this e-mail is intended only for the person to whom it is addressed. If you believe this e-mail was sent to you in error and the e-mail contains patient information, please contact the Partners Compliance HelpLine at http://www.partners.org/complianceline . If the e-mail was sent to you in error but does not contain patient information, please contact the sender and properly dispose of the e-mail.
Dear Ruopeng,
Thank you for the information.
best Peng
On Fri, Jan 27, 2017 at 4:10 PM, Ruopeng Wang rpwang@nmr.mgh.harvard.edu wrote:
Hi Peng,
No, there is no command-line option for that. I will add it in future update.
Best, Ruopeng
On Jan 27, 2017, at 9:49 AM, peng prion.w@gmail.com wrote:
Dear Freesurfer experts,
When I use Freeview GUI to show overlays on a surface, I can click on the button "Configure", and then check the box "Enable" in the smooth section (upper right of the pop-out window), to smooth it. Is there any options to do similar stuff in the command line of freeview? e.g. when I want to generate a lot of screenshots by the -ss option. Thank you in advance!
best Peng _______________________________________________ Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
The information in this e-mail is intended only for the person to whom it is addressed. If you believe this e-mail was sent to you in error and the e-mail contains patient information, please contact the Partners Compliance HelpLine at http://www.partners.org/complianceline . If the e-mail was sent to you in error but does not contain patient information, please contact the sender and properly dispose of the e-mail.
freesurfer@nmr.mgh.harvard.edu
-
Bruce Fischl -
peng -
Ruopeng Wang