Him
the disk space doesn't seem to be problem - at least mne_analyze and tksurfer are working fine with other subjects with the same space.
Best regards, Onerva K.
Quoting Bruce Fischl fischl@nmr.mgh.harvard.edu:
usually that means you ran out of disk space. Did you check?
cheers Bruce On Mon, 28 Jun 2010, Onerva Korhonen wrote:
Hi all,
I have problems with mne_analyze - I need to do the coordinate alignment, but when I try to load the inflated surface (or in fact any surface), I get error message:
mne_read_int could not read data
Inflated surface doesn't work with tksurfer either. Instead I get a message:
freadFloat: fread failed
I don't know if it would say something more later - there seems to be a loop, so I have killed the program at this point.
I have no idea what to do - redoing recon-all doesn't seem to help. So I hope someone could help me with this.
Many thanks, Onerva K.
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
The information in this e-mail is intended only for the person to whom it is addressed. If you believe this e-mail was sent to you in error and the e-mail contains patient information, please contact the Partners Compliance HelpLine at http://www.partners.org/complianceline . If the e-mail was sent to you in error but does not contain patient information, please contact the sender and properly dispose of the e-mail.
I meant did you run out of it. Is there any space left on that partition? Did recon-all.log have any error messages in it (typically at the end)?
cheers, Bruce
On Tue, 29 Jun 2010, Onerva Korhonen wrote:
Him
the disk space doesn't seem to be problem - at least mne_analyze and tksurfer are working fine with other subjects with the same space.
Best regards, Onerva K.
Quoting Bruce Fischl fischl@nmr.mgh.harvard.edu:
usually that means you ran out of disk space. Did you check?
cheers Bruce On Mon, 28 Jun 2010, Onerva Korhonen wrote:
Hi all,
I have problems with mne_analyze - I need to do the coordinate alignment, but when I try to load the inflated surface (or in fact any surface), I get error message:
mne_read_int could not read data
Inflated surface doesn't work with tksurfer either. Instead I get a message:
freadFloat: fread failed
I don't know if it would say something more later - there seems to be a loop, so I have killed the program at this point.
I have no idea what to do - redoing recon-all doesn't seem to help. So I hope someone could help me with this.
Many thanks, Onerva K.
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
The information in this e-mail is intended only for the person to whom it is addressed. If you believe this e-mail was sent to you in error and the e-mail contains patient information, please contact the Partners Compliance HelpLine at http://www.partners.org/complianceline . If the e-mail was sent to you in error but does not contain patient information, please contact the sender and properly dispose of the e-mail.
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
freesurfer@nmr.mgh.harvard.edu
-
Bruce Fischl -
Onerva Korhonen