Hi list, this error is still occurring:
mri_convert $SUBJECTS_DIR/subj/mri/MRS_MASK.nii.gz $SUBJECTS_DIR//subj/mri/MRS_MASK.mgz fcseed-config -segid 1 -seg $SUBJECTS_DIR//subj/mri/MRS_MASK.mgz -fsd rest -mean -cfg MRS_MASK.config fcseed-sess -s -cfg MRS_MASK.config
During
fcseed-sess -s subj -cfg MRS_MASK.config
Voxel Volume is 64.5752 mm^3 Generating list of segmentation ids Found 1 segmentations Computing statistics for each segmentation 0 1 0 0.000 MRIalloc(0, 1, 1): bad parm Reporting on 0 segmentations Computing spatial average of each frame
Writing to /Applications/freesurfer/subjects/fMRI/sub/rest/001/tmp. fcseed-sess.97908/avgwf.mgh Segmentation fault
I have read your previous message and you can check the MRS voxel features. MRS voxel mask is in subj directory where I have run recon all -all.
data_type FLOAT32 dim1 256 dim2 256 dim3 256 dim4 1 datatype 16 pixdim1 1.000000 pixdim2 1.000000 pixdim3 1.000000 pixdim4 0.010747 cal_max 0.0000 cal_min 0.0000 file_type NIFTI-1+
The features are same of other subject that runs fine. data_type FLOAT32 dim1 256 dim2 256 dim3 256 dim4 1 datatype 16 pixdim1 1.000000 pixdim2 1.000000 pixdim3 1.000000 pixdim4 0.010747 cal_max 0.0000 cal_min 0.0000 file_type NIFTI-1+
Thank you very much.
Stefano
----Messaggio originale---- Da: stdp82@virgilio.it Data: 16-ott-2015 23.15 A: freesurfer@nmr.mgh.harvard.edu Ogg: [Freesurfer] R: Re: R: import FS-FAST results in FSL
I'd like to open with FSLview the sig.nii.gz which is produced by selxavg3-sess. If I use mri_surf2vol, which is the template to added in --template? It should be in Tailairach space? Where can I find the template that
I
should added? Thanks,
Stefano
subj/rest/fc.seed.surf.lh/L_seed/sig.nii.gz data_type FLOAT32 dim1 27307 dim2 1 dim3 6 dim4 1 datatype 16 pixdim1 1.000000 pixdim2 1.000000 pixdim3 1.000000 pixdim4 1100.000000 cal_max 49.1815 cal_min -12.3855 file_type NIFTI-1+
Thanks,
Stefano
----Messaggio originale---- Da: greve@nmr.mgh.harvard.edu Data: 29-set-2015 22.09 A: freesurfer@nmr.mgh.harvard.edu Ogg: Re: [Freesurfer] R: import FS-FAST results in FSL
Do you mean surface-based analysis? You'd have to put them back
into
the
volume using mri_surf2vol, write them out as nifti and then run
fslview
on them
On 09/29/2015 11:17 AM, stdp82@virgilio.it wrote:
Hi list, I would like to import FS-FAST results (conjunction maps) inFSL,
opening them by fslview. Could you provide me any suggestion? Thank you very much Best regards, Stefano
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
-- Douglas N. Greve, Ph.D. MGH-NMR Center greve@nmr.mgh.harvard.edu Phone Number: 617-724-2358 Fax: 617-726-7422
Bugs: surfer.nmr.mgh.harvard.edu/fswiki/BugReporting FileDrop: https://gate.nmr.mgh.harvard.edu/filedrop2 www.nmr.mgh.harvard.edu/facility/filedrop/index.html Outgoing: ftp://surfer.nmr.mgh.harvard.
edu/transfer/outgoing/flat/greve/
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer
The information in this e-mail is intended only for the person to
whom it is
addressed. If you believe this e-mail was sent to you in error and
the e-mail
contains patient information, please contact the Partners
Compliance
HelpLine at
http://www.partners.org/complianceline . If the e-mail was sent to
you in error
but does not contain patient information, please contact the sender
and properly
dispose of the e-mail.
Freesurfer mailing list Freesurfer@nmr.mgh.harvard.edu https://mail.nmr.mgh.harvard.edu/mailman/listinfo/freesurfer